Author Topic: DG600F Coin accepter  (Read 5420 times)

Rocketpip

  • Guest
DG600F Coin accepter
« on: December 03, 2011, 01:20:08 AM »
I have a DG600F coin accepter pre-installed on my jukebox.
It did work with a previous software so its installed correctly.
I've read the specs so many times my eyes are almost bleeding.
JukeBlaster software just ignores it (like its not even there)
Running windows xp pro.
Can anyone please help?
Thanks,
Rod

Dj4nrv

  • Sr. Member
  • ****
  • Posts: 353
Re: DG600F Coin accepter
« Reply #1 on: December 03, 2011, 12:25:58 PM »
How do you have the coin mech connected to the pc?

Rocketpip

  • Guest
Re: DG600F Coin accepter
« Reply #2 on: December 03, 2011, 10:02:00 PM »
Its running through a CP210x USB to UART Bridge on Com 3

jukejohn

  • Hero Member
  • *****
  • Posts: 745
Re: DG600F Coin accepter
« Reply #3 on: December 05, 2011, 11:13:59 AM »
is this a serial to usb problem which i have come across in the past  its never straight forward ive had various probs with usb conversion from serial might be worth looking on the net i found this page if it helps
http://www.silabs.com/products/interface/usbtouart/Pages/usb-to-uart-bridge.aspx

Dj4nrv

  • Sr. Member
  • ****
  • Posts: 353
Re: DG600F Coin accepter
« Reply #4 on: December 05, 2011, 01:11:48 PM »
this is why we have coin kit!! ;D

Rocketpip

  • Guest
Re: DG600F Coin accepter
« Reply #5 on: December 05, 2011, 04:46:21 PM »
Will look at the link today, thanks for your help!

As for the other post, the reason for not having your coin accept, the jukebox came with one and I was convinced by someone here it was compatible  ::) your concern is noted.

jukejohn

  • Hero Member
  • *****
  • Posts: 745
Re: DG600F Coin accepter
« Reply #6 on: December 05, 2011, 05:47:20 PM »
its likely that it works ok but the key output will need remaping to f1
for credits with vjb you can pm me if you get stuck think i might be able to help

Dj4nrv

  • Sr. Member
  • ****
  • Posts: 353
Re: DG600F Coin accepter
« Reply #7 on: December 05, 2011, 06:07:36 PM »
Sorry didn't mean to be that abrupt!
I fully understood that you had a pre existing setup.
I merely meant to point out that we have coin kit to avoid the hassle of fault finding like you are currently experiencing.
and As its new I wasn't sure if you had considered the coin kit option?
Good luck anyhow.  ;D

Rocketpip

  • Guest
Re: DG600F Coin accepter
« Reply #8 on: December 06, 2011, 02:48:32 AM »
its likely that it works ok but the key output will need remaping to f1
for credits with vjb you can pm me if you get stuck think i might be able to help
Hi there JJ.
yeah, i'm stuck. Sure could use some guidance.
I dont see anything in my device manager that has a RS232.
Could that be part of my issue?
It does show the "Silicon Labs CP210x USB to UART Bridge (COM3)" under ports (no conflicts)

jukejohn

  • Hero Member
  • *****
  • Posts: 745
Re: DG600F Coin accepter
« Reply #9 on: December 06, 2011, 01:01:29 PM »
ok go to my profile and click on send user private message and ill help you out tonight
it will be to long winded to doit through the forum messsages if it gets that bad
can even guide you over the phone   ;)

Rocketpip

  • Guest
Re: DG600F Coin accepter
« Reply #10 on: December 07, 2011, 03:41:22 AM »
Hey there JukeJohn,
I'm really not familiar with this site.
Where do I go to start PM with you?
Thanks.

jukejohn

  • Hero Member
  • *****
  • Posts: 745
Re: DG600F Coin accepter
« Reply #11 on: December 07, 2011, 01:18:08 PM »
just sent you private message you can link to me from that

yes its not easy i had to dig deep before i found this option